Tout sur les atténuateurs de puissance (recap p1)

Rappel du dernier message de la page précédente :
The Trout
Je sens que je vais faire modifier mon SPL moi
“The type of cap is not as important as the value of the cap, for guitar. In an Amp, your cap type is much more important, as the signal is being passed through the cap all the time. In a guitar, you’re not hearing the cap itself, you’re hearing what the cap is impeding”. Lindy Fralin
Scorpion1211
Etonnant qu'aucun constructeur n'y ai pensé avant.
The Trout
Oui, on trouve souvent une sortie niveau ligne mais pas de retour! Enfin dans ceux que je connais du moins.
“The type of cap is not as important as the value of the cap, for guitar. In an Amp, your cap type is much more important, as the signal is being passed through the cap all the time. In a guitar, you’re not hearing the cap itself, you’re hearing what the cap is impeding”. Lindy Fralin
Scorpion1211
Ca y est, ils m'ont répondu!

Je vous copie le mail, attention, c'est long! Mais y a tous les détails.

Citation:
Laurent,

The attenuator will work with any 4,8 or 16 ohm speaker, it can also be made to work with 2 ohms if necessary. The effects loop works well with any time based effects like delay. The effects and your amp's tone travel separability towards the speaker, where they are blended together. There is a send, return jack plus send level control as well as the amp and speaker jacks. Payments can be made by credit card, paypal bank transfer or money order. It would take 7 days or less to assemble and mail a unit. You can call 1-604-432-6009 with your credit card details between 11:00 - 5:30 Pacific time m-f or 12:00 - 3:00 sat. All figures are in Canadian dollars. The loop is mainly for time based effects like delay,reverb, chorus, echo. The effects come at the end of the chain, it doesn't interfere with your main tone especially delay. If you only have a 50w amp, then a 50w for home and live , a 50w attenuator would be sufficient.

220v

100w output basic $360
50w output basic $300
10w output basic $225( if you only need it for the bedroom)

Shipping:
50/100w
single volume
air: 132
surface 72

dual volume
air( 5 business days): 140
surface(4 to 6 weeks): 78


options

dual volume fsw $80 -> give you 2 master volumes, you can use it as a volume boost or have one for high for clean and low for dirty. Volumes will be changeable via foot switch.
200w load $25 -> if you plan on using a 100w plus amp or old Marshall's like a 1950's jmp, absorbs up to 200w of power
line out $25 -> send the attenuated signal out.
Plexi Sw $25 -> the attenuator smooths the high end sizzle, plexi add the sizzle ,brightness, back to the amp.

effects loop $80 : A single speaker wet/dry system if you use delay, chorus, echo, reverb pedals you will notice a big difference in sound. delay makes a big difference through this loop rather than in front of the guitar or in your amp's loop. If you want need more info on this option from other users, I can provide you some contact info.
effects loop foot switchable +40 -> turn the effects loop on or off via foot switch. You can bypass the effects with the foot switch.

200v variac out 25-> provides your amp with 200v of power instead of 2200v. You amp's tube will last longer and the amp will run cooler. The sound is softer, not as harsh.
Bedroom Sw $25 -> give you a 0-5w volume range, instead of a 0-100w range. The volume control will become less sensitive. You will get a greater usable volume range to use at home.
headphone jack $25 -> disables the speaker and outputs the sound to your headphones.
rack mount $40 -> a rack mount case
bypass $25 -> bypass the attenuator with a switch, must stop playing before using the switch

solid state overdrive $60 -> overdrive your amp at a lower volume, while still getting a tube overdrive plus a tighter bottom and crispier highs. It contains an additional circuit plus a switch to turn it on or off. It can also be made to turn on or off via foot switch. Usually you would turn the master volume of your amp to about 6 or 7 to overdrive the power tubes. Now you would be able to have the amp's master volume at maybe 5, where the power tubes begin to overdrive. Then you will be overdriving the additional solid state module inside and still getting a tube overdrive sound, with a lower master volume.
Foot switchable overdrive +40 -> turn the ss overdrive on or off via footswitch.

wattage doubler $30 -> can make any small amp louder double or triple the wattage . Could make a small amp sound like a hundred watt amp.


Bryan


Je lui ai répondu et j'ai passé commande d'un modèle 50W single volume, avec plexi switch et boucle d'effet, je n'ai pas besoin de plus.
Avec ces options + les frais de port by air + si je prévois les frais de douane et TVA, ça me reviendrait à environ 526€.
C'est donc un peu cher au total (y a moyen de bien baisser les frais de port si on n'est pas pressé), mais ça me tente vraiment. De plus je suis tombé sur quelques reviews sur des sites américains, que du positif! Ce modèle a apparemment été choisi par des pointures, comme Bonamassa, Satriani ou Josh Homme.
The Trout
Il a l'air bien ouais, le mec propose pleins d'options super intéressantes. Il assome bien sur les frais de port par contre, ou alors le truc pèse un âne mort genre Aracom, c'est fort possible.

Quand je lis son mail ça n'aurait pas été plus secure de prendre un 100w avec ton Metro?
J'ai toujours lu qu'il fallait prendre le double en puissance sur les "gros" amplis, surtout un plexi qui doit avoir des peaks bien violents vu la dynamique du bestiau.
“The type of cap is not as important as the value of the cap, for guitar. In an Amp, your cap type is much more important, as the signal is being passed through the cap all the time. In a guitar, you’re not hearing the cap itself, you’re hearing what the cap is impeding”. Lindy Fralin
Scorpion1211
Je lui ai bien précisé que j'avais un Marshall tout lampes 50W. Je ne pense pas qu'il en soit à son premier atténuateur pour ce genre d'ampli, il doit savoir ce qu'il fait.
Par contre je crois comprendre qu'on ne peut pas mettre d'effet genre booster dans la boucle. Je lui ai renvoyé un mail pour demander, parce que du coup l'option Dual Volume va être intéressante pour moi. Mais là je prendrais peut-être l'envoi normal pour réduire les frais.
The Trout
L'envoi "normal" c'est par mer, tu vas le recevoir dans 10 ans nan?

Tu lui as dit que ton Marshall 50 watts était un plexi?
Oui la boucle est plutôt dédiée aux effets qui n'apportent pas de gain. En même temps, un booster après l'etage de puissance bof quoi
“The type of cap is not as important as the value of the cap, for guitar. In an Amp, your cap type is much more important, as the signal is being passed through the cap all the time. In a guitar, you’re not hearing the cap itself, you’re hearing what the cap is impeding”. Lindy Fralin
Scorpion1211
The Trout a écrit :
L'envoi "normal" c'est par mer, tu vas le recevoir dans 10 ans nan?

Tu lui as dit que ton Marshall 50 watts était un plexi?
Oui la boucle est plutôt dédiée aux effets qui n'apportent pas de gain. En même temps, un booster après l'etage de puissance bof quoi


4 à 6 semaines de délai pour l'envoi par mer.

Oui oui, j'ai précisé Plexi.
Scorpion1211
Bon voilà, donc effectivement, la boucle est plutôt faite pour les effets de type "retard" (delay, reverb, etc...).

J'ai donc modifié ma commande, et pris un modèle Dual Volume, afin d'avoir un boost de volume disponible pour les solos.

Total avec frais de port : 506€.
Pour les frais de douane on verra, mais il dit qu'il déclare une valeur très inférieure pour les diminuer.
Scorpion1211
Un petit retour sur le Ho's Attenuator, après utilisation en répète.

Alors il n'a pas l'air de trop colorer le son, mais difficile de comparer puisque je n'ai pas d'autre atténuateur. Le switch "Plexi" est indispensable de mon avis pour les fortes atténuations, ça corrige bien l'égalisation.
La fonction dual volume, ça le fait grave! Plus besoin d'aucun boost pour les solos!

Ensuite la boucle... Pour le moment pas convaincu. C'est une boucle parallèle, et je ne suis pas habitué à ça, j'ai toujours eu des boucles en série, donc à mon avis je ne règle pas ça comme il faut.
De plus, j'ai vu, seulement après mes essais, qu'il vaut mieux pour les delays les mettre en fonction "killdry" (mode où l'on entend uniquement les répétitions). Je vais donc réessayer ça, et je verrai ce que ça donne.
Je me questionne du coup : s'il faut mettre les delays en killdry pour que ça sonne, qu'en est-il des reverbs? Régler à fond? Faudrait que je teste, mais j'ai pas de reverb et du coup j'ai pas envie d'en acheter avant d'être sûr de l'utilisation.

Voilà pour la première impression!
jerem37
  • jerem37
  • Vintage Total utilisateur
Mark Twang a écrit :
Scorpion1211 a écrit :
Hello!

Des infos sur ce modèle d'atténuateur? http://hoelectronics.com/wordp(...)ator/

Il a plutôt l'air intéressant, et surtout, une chose m'interpelle. Dans les options, on voit "effects loop"...

Image trouvée sur le net :


Serait-ce un atténuateur permettant de brancher des effets après la section puissance?? J'ai peine à le croire!

Je fais la fiche du modèle, et ce que je vois moi, c'est ça :



Soit une entrée amp, une sortie HP, une Line Out (pour la DI ?) et un insert pour footswitch (?).

EDIT - Ok : il y a une chiée d'options disponibles.


Salut les gars,

intéressant ça, très intéressant...
J'ai jamais pigé pkoi parmi tous les atténuateurs personne de faisait l'option footswitch pour pouvoir couper l'atté quand on veut et être bypassé....
Moi c'est ça que j'aurai voulu sur ma hotplate, pour que j'atténue uniquement le canal lead qui hurle à 3/10 au volume, mais pas le clean qui est à peine au même niveau quand il est à 5-6/10...
Scorpion, c'est bien ça la fiche footswitch alors? Tu as pris cette "option"?
---Partisan de la lutte contre les coupeurs de médiums!!!---
Scorpion1211
Oui c'est ça le footswitch. Mais ce n'est pas une sélection entre atténuation et bypass de l'atténuateur, c'est un switch entre deux volumes d'atténuation.
On règle le premier en atténuation comme on le souhaite, le second avec moins d'atténuation pour passer en solo par exemple, ou alors dans ton cas jerem, sans atténuation (bouton de réglage au max).

Euh... je sais pas si je suis clair...
The Trout
Sisi
“The type of cap is not as important as the value of the cap, for guitar. In an Amp, your cap type is much more important, as the signal is being passed through the cap all the time. In a guitar, you’re not hearing the cap itself, you’re hearing what the cap is impeding”. Lindy Fralin

En ce moment sur ampli et préampli guitare...